- What are electromagnetic fields?
- Static and low-frequency fields
- What are static and low-frequency electric and magnetic fields?
- Direct and alternating voltage
- Effects of static and low-frequency fields
- Reports & Evaluations
- Radiation protection relating to the expansion of the national grid
- Basics transfer of electrical power
- High-frequency fields
- What are high-frequency fields?
- Applications high-frequency fields
- Radiation protection in mobile communication
- What is mobile communication?
- Reports and evaluations
- What is optical radiation?
- UV radiation
- What is UV radiation?
- Sun but safe!
- Effects of UV radiation
- Protection against UV radiation
- UV index
- Infrared radiation
- What is ionising radiation?
- Radioactivity in the environment
- Where does radioactivity occur in the environment?
- What is the level of natural radiation exposure in Germany?
- Air, soil and water
- Building materials
- Industrial residues (NORM)
- BfS laboratories
- Applications in medicine
- Radiation protection in medicine: international activities
- Applications in daily life and in technology
- Radioactive radiation sources in Germany
- Register high-level radioactive radiation sources
- Type approval procedure pursuant to RöV and StrlSchV
- Cabin luggage security checks
- Radioactive materials in watches
- Ionisation smoke detectors (ISM)
- What are the effects of radiation?
- Acute radiation damage
- Effects of selected radioactive materials
- Consequences of a radiation accident
- Cancer and leukaemia
- Genetic radiation effects
- Individual radiosensitivity
- Epidemiology of radiation-induced diseases
- Ionising radiation: positive effects?
- Risk estimation and assessment
- Radiation protection
- Basic informations
- Occupational radiation protection
- Nuclear accident management
- What happens in an emergency?
- Federal and state tasks
- In the event of an emergency
- Measuring networks
- Exercises for emergency situations
- Nuclear accidents
- Defence against nuclear hazards
- Service offers
- Radon measurements
- Incorporation monitoring
- Biological dosimetry
- Online library
- About us
- Science and research
- Research concept
- Scientific collaborations
- EU research framework programme
- BfS research programme
- Third-party funded research
- Departmental research
- Selected research projects
- Selected research results
- Professional opinions
- Laws and regulations
- BfS Topics in the Bundestag
Mobile telephone networks of the third generation (3 G) have been operating in Germany since 2004. They are based on the digital transmission standard UMTS (Universal Mobile Telecommunications System). The frequency range allocated to the networks is between 1920 and 2170 MHz. Other mobile radio frequencies can be used as well. 3G is sometimes also referred to as WCDMA. The abbreviation is derived from the initials of the channel access method Wide Code Division Multiple Access employed by UMTS.
As with GSM technology, the areas to be served are divided into so-called cells, each of which is supplied by stationary transmitter stations (base stations). At a base station, often three antennas are installed which provide three sectors, each covering an angle of 120°, with one radio channel each.
In UMTS-networks data are transferred differently than in GSM: no set frequency channels and time slots are allocated to individual connections, but all network subscribers use the available frequency band at the same time. UMTS systems typically operate at a channel bandwidth of 5 MHz. The single data streams are identified by an individual code and are spread to the width of the available frequency band. Using the known code, the data stream intended for the receiver is then decoded by the receiver from the received signal mixture.
Higher data transmission rate makes UMTS networks multimedia capable
A significantly higher data transmission rate can be achieved with UMTS than with GSM and the data transfer methods GPRS (General Packet Radio Service) and EDGE (Enhanced Data Rates for GSM Evolution) based on GSM. UMTS networks are multimedia capable, that is, they can transfer images, sound and data. However, the networks are also used for traditional mobile telephony.
Frequency division duplexing
So-called frequency division duplexing is preferably used to distinguish the data sent by the base station from that sent by the mobile phone according to the information provided by the producers. This means that another frequency band is used for the connection from the base station to the mobile phone than in the opposite direction. The signal has a noise-like character.
Another possibility is so-called time division duplexing. Here the same frequency band is alternately used in both directions of the connection. The signal is pulsed. This method is currently only intended for smaller networks such as company internal networks.
Fine and fast adjustment of the transmitter power ensures the trouble-free operation of a UMTS network. This applies to base stations as well as to mobile terminals. To minimise mutual interference, the handsets operate at the lowest possible transmitter power levels.
During connection setup the transmitter power is increased in quick succession only until a stable connection between terminal and base station has been established. Compared to GSM networks, terminals in UMTS networks show opposite behaviour: In GSM networks a high transmitter power is used at the beginning of a connection setup. The transmitter power is reduced to the required level only after the connection has been established.
With the mobile communications standards HSPA (High Speed Packet Access) and HSPA+ based on UMTS even a higher data transmission rate can be achieved than with the original UMTS technology. The improvements originate mainly from the introduction of superior modulation techniques and improved antenna technologies.
State of 2018.01.17